Performance and Technical data

  • EASYFLEX C-111 adhesive is polymer, modifier & additives. it is used for fixing ceramic tiles. apply outdoor and indoor area and vitrified tiles indoor only.EASYFLEX C-111 is a bagged cementations powder to be mixed with either water for installing.

    Designed for fixing all ceramic tiles on internal & external and vitrified tiles Internal only.


    • Packaging : 20 kg Bags   
    • Coverage : Approx. 55-60 sq.ft. per 20 kg bag. 
    • Color : Grey
    • Certification
      Meets the following standards as per
      • IS 15477 Type-1
      • EN 12004/ISO 13007:C1T

How to Use


The surface to be covered with Ceramic tile shall be sound and conform to good design, rigid, clean and free of dirt, oil, grease, curing compounds, form release agents or loose plaster and paint. For economy, the surfaces should be level and true within: Walls – 3mm in 2.5m Floors – 1.5mm in 1.0m

Surface Preparation:

  • If a plaster/leveling mortar bed is applied, ensure that it is cured for at least 7 days to achieve proper strength before application of tile adhesive for installation of tile
  • Ensure the substrate is clean and free from impurities like dust, dirt, debris, oil, grease, curing agents, loose plaster, etc
  • Dampen the wall before application of thin set adhesive
  • Clean the back of tile for any dust or coating


The products can be mixed by hand or slow speed electric drill mixer (less than 300 rpm). Pour potable clean water in a clean container and then add the powder ULTRAFLEX C-222 and mix until the mixture becomes creamy and plastic. Do not over mix. Leave the mix to slake for 5-10 min and remix before use. Mix only sufficient quantity of adhesive for an immediate need.


Approximately 1 bag of ULTRAFLEX C-222 with 5-6 ltrs of water. Adjust the quantity of liquid to obtain proper consistency.


  • Wet the surface and remove the excess water before applying the adhesive. Ensure the area is shaded from sunlight. The adhesive shall be applied with the flat side of the trowel using a scraping motion to work the material into good contact with the surface to be covered.
  • Additional mortar is then applied with the notched edge of the trowel.
  • When installing large tiles, spread adhesive onto the back of tile in addition to trowelling material over a surface to be tiled. Select proper type of notched trowel.

a) Thin Tiles up to size 300 X 300 mm (1’X1’), use a square notched trowel of size 6mm X 6mm to provide a total thickness of 3mm

b) Large Porcelain Tiles upto 450 X 450 mm with ribs, use a square notched trowel of size 6mm X 6mm and back butter the tiles with the same adhesive to a thickness of 1-1.5mm to provide a total thickness of 4.5mm

c) Large Porcelain Tiles upto 600 X 600 mm (2’X2’) with ribs, use a square notched trowel of size 6mm X 9mm and back butter the tiles with the same adhesive to a thickness of 1-1.5mm to provide a total thickness of 6mm

  • The most important standard to keep in mind is to insure that the piece of tile is completely bedded in the mortar or adhesive with 100% coverage.
  • Rear face of tiles (especially Porcelain tiles) should be cleaned with damp sponge to clean all the dust. Do not saturate in water.
  • Excess mortar on adhesive shall be cleaned from the surface of the stone with wet cloth or sponge while the mortar is fresh.

Areas of Application 

Designed for interior floor & wall applications  

Suitable Substrates

  • Cement Mortar Beds
  • Brick Masonry
  • Cement Terrazzo
  • Cement Plaster


  • Extended open time
  • Smooth & Creamy
  • Ideal for fixing small and medium size tiles on floor & wall


Image description
Download Brochures

About Us

We are world class – international standard wide range construction chemicals manufacturer, consultant, supplier, advisor, and turnkey project undertaker with speciality construction chemical application in civil construction work.

Stay in Touch

Survey No. 123, Plot No.7, Road - D , GIDC Estate, Visnagar-384315.